АвтоАвтоматизацияАрхитектураАстрономияАудитБиологияБухгалтерияВоенное делоГенетикаГеографияГеологияГосударствоДомДругоеЖурналистика и СМИИзобретательствоИностранные языкиИнформатикаИскусствоИсторияКомпьютерыКулинарияКультураЛексикологияЛитератураЛогикаМаркетингМатематикаМашиностроениеМедицинаМенеджментМеталлы и СваркаМеханикаМузыкаНаселениеОбразованиеОхрана безопасности жизниОхрана ТрудаПедагогикаПолитикаПравоПриборостроениеПрограммированиеПроизводствоПромышленностьПсихологияРадиоРегилияСвязьСоциологияСпортСтандартизацияСтроительствоТехнологииТорговляТуризмФизикаФизиологияФилософияФинансыХимияХозяйствоЦеннообразованиеЧерчениеЭкологияЭконометрикаЭкономикаЭлектроникаЮриспунденкция

Q.7 What is the most commonly used exterior routing protocol ?

Читайте также:
  1. Which protocol supports rapid delivery of streaming media:RTP
  2. Обходим ограничения с IP Source Routing

 

BGP

RIP

OSPF

EIGRP

 

Q.8 Refer to the exhibit. The network administrator needs to configure the router with a name. Which command will the administrator use to configure the router name?

 

Router# ip hostname Boise

Router# enable hostname Boise

Router(config-line)# name Boise

Router(config)# hostname Boise

Router(config)# ip hostname Boise

 

 

Q.9 Why are port numbers included in the TCP header of a segment?

 

to indicate the correct router interface that should be used to forward a segment

to identify which switch ports should receive or forward the segment

to determine which Layer 3 protocol should be used to encapsulate the data

to enable a receiving host to forward the data to the appropriate application

to allow the receiving host to assemble the packet in the proper order

 

 

Q.10 What is the purpose of the routing process?

 

to encapsulate data that is used to communicate across a network

to select the paths that are used to direct traffic to destination networks

to convert a URL name into an IP address

to provide secure Internet file transfer

to forward traffic on the basis of MAC addresses

 

 

Q.11 Which two statements are true about the use of the debug ip rip command on a Cisco router? (Choose two.)

 

The debug ip rip command displays RIP routing activity in real time.

The debug ip rip command can be issued at the user EXEC configuration mode.

The debug ip rip command displays a combination of the information that is displayed by the show ip route and show ip protocols commands.

Because of router processor usage, the debug ip rip command should be used only when necessary.

The debug ip rip command should be used instead of the show ip route command whenever possible.

 

 

Q.12 What minimum configurations must be set on a host to allow a request to be sent tohttp://www.cisco.com/? (Choose four.)

 

DNS server

WINS server

IP address

NetBIOS

subnet mask

default gateway

 

 

Q.13 A Catalyst 2960 switch has been taken out of storage to be used as a temporary replacement for another switch that needs to be repaired. About a minute after the switch has started, the SYST LED on the front of the switch transitions from blinking green to amber. What is the meaning of the amber SYST LED?

 

The switch has no configuration file in NVRAM.

The switch has failed POST and must be sent for service.

The switch is functioning properly.

The switch is in half-duplex mode.

 


1 | 2 | 3 | 4 | 5 | 6 |

Поиск по сайту:



Все материалы представленные на сайте исключительно с целью ознакомления читателями и не преследуют коммерческих целей или нарушение авторских прав. Студалл.Орг (0.004 сек.)