Questions between : № 1-222, 294-360 – AutoCAD

№ 223-293 – 3DsMAX

$$$1. To reverse the UNDO command the correct entry is –

$$ REDO

$ REDRAW

$ ESC

$ U

$$$2. Which of the following statements is true –

$$ ZOOM ALL will reach beyond the drawing limits if an object is there

$ ZOOM ALL only reaches out to the drawing limits

$ There is not real difference between ZOOM AL and ZOOM E

$ ZOOM ALL makes all objects visible irrespective of the layer visibility state

$$$3. The command to scale a paper space viewport to half the drawn size is –

$ Zoom 0.5x

$ Zoom 1/2x

$ Zoom 2xp

$$ Zoom 0.5xp

$$$4. Which of the following options of the UNDO command allows the undo facility to be disabled?

$$ AUTO

$ CONTROL

$ END

$ GROUP

$$$5. Which of the following commands forces AutoCAD to revise the entire drawing taking into account the effect of changes within the system?

$$ CHANGE

$ REDO

$ REDRAW

$ REGEN

$$$6. Which of the following commands allows simultaneous pan and zoom?

$$ ZOOM DINAMIC

$ ZOOM EXTENTS

$ ZOOM CENTER

$ ZOOM PAN

$$$7. Which of the following commands CANNOT be undone?

$ XREF

$ SETVAR

$$ SAVE

$ LIST

$$$8. The MAXIMUM number of commands whose effect can be undone by the UNDO command is?

$ 256

$ 1000

$ all the command issued since the drawing was first created

$$ all commands issued since the drawing was last loaded into the drawing editor

$$$9. Which of the following commands would be used to limit the movement of the cursor to specified increments?

$ AXIS

$ GRID

$ ORTHO

$$ SNAP

$$$10. Which one of the following commands can be used to turn the grid through 45 degrees?

$$ 1:1

$ 1:10

$ 1:100

$ 1:1000

$$$11. Which of the following BEST defines a ’prototype’ or ‘template’ drawing?

$ the drawing which is currently being edited by AutoCAD

$ a drawing used to store a library of standard symbols

$$ a meaning of setting the initial drawing environment for new drawings

$ a file which holds details of the display, digitiser, and plotters

$$$12. In order for the grid command to work correctly two settings have to be established

$ the correct limits set and an appropriate setting of the grid value set

$ limits set to ON and an appropriate setting of the grid value set

$$ Snap and Osnap set

$ gridmode and osmode both set to 1

$$$13. When using AutoCAD for the design of a mechanical component measuring 1000mm by 500mm, the dimensions would normally be entered at a scale of?

$$ 1:1

$ 1:2

$ 1:5

$ 1:10

$$$14. How many entity colours does AutoCAD support?

$$ 255

$ 16

$ unlimited

$ 64

$$$15. A house measures 15000mm x 8000mm in plan view. When drawing the plan view only which one of the following sets of limits would be BEST to use?

$$ 0,0/20000,15000

$ 0,0/20,15metres

$ -2000,-2000/20000,15000

$ -2000,-2000/15000,8000

$$$16. What option would be selected following the TEXT command to set a different type of text to that currently in use?

$$ NEW

$ FONT

$ SET

$ STYLE

$$$17. The special character string that causes text to be undefined is –

$ u%%

$ %%u

$ %u%

$$ %u

$$$18. Which of the following is an AutoCAD font for mathematical symbols?

$$ MATHC

$ MATHFONT

$ MATHSYM

$ SYMATH

$$$19. The effect of QTEXT being ON is to?

$ place txt directly in the drawing as defined

$$ speed up drawing regeneration by replacing text within rectangles

$ use simplified text font to replace complex text font

$ allow automatic line spacing of textual input

$$$20. The text option that prompts the user for two endpoints and then automatically calculates the text height and positions the text between the two points is chosen from this AutoCAD prompt Align/Fit/Center/Middle/Right/TL/TC/TR/ML/MC/MR/BL/BC/BR

Which one is correct?

$$ center

$ Align

$ TR

$ Fit

$$$21. Which of the following commands will NOT place some form of text within the drawing-

$ MTEXT

$ DTEXT

$$ STYLE

$ ATTDEF

$$$22. When is a space NOT interpreted as the enter key?

$ when entering text

$ When using the PEDIT command

$ When selecting objects

$$ The space is always an alternative to the enter key

$$$23. The special character string that is used to print the diameter sign is –

$$ %%c

$ %%d

$ %dia

$ c%%

$$$24. Which one of the following is an AutoCAD relative polar coordinate?

$ 30,81

$ @81,30

$ 30<81

$$ @81<30

$$$25. You are designing a floor plan and know the length and angle of one of the wall segments to be 1500mm and 30 degrees/ this is to be followed by a wall 2000mm long at 90degrees to the first. Which one of the following is the correct input?

$ @1500,30 @2000<120

$$ 1500<30 @2000<90

$ @1500<30 @2000<90

$ @1500<30 @2000<120

$$$26. Which one of the following would draw a vertical line 30 units in length from a previously defined point given as 30,50?

$ 60,50

$$ 30,80

$ @30,0

$ @30<0

$$$27. Which one of the following statements is true?

$$ The origin of a User Coordinate System can be relocated anywhere in the World Co-ordinate system

$ Drawing entities are assigned to a User Coordinate system and thereafter the UCS cannot be deleted from the drawing

$ A drawing cannot have more than four User Co-ordinate systems active at any one time

$ The UCS icon cannot be turned off

$$$28.

The shape above is based on a 10 unit module. Which is the correct set of codes to draw this shape, starting at the lower left and moving anti clock wise?

$ 0,0 10,0@10<45 10,10 0,20 0,30 c

$$ 0,0 10,0@10,10 10,10@0,20 0,30 c

$ 0,0@10<0 20,10 10,10 1030 30,0 c

$ 0,0@10,0@10,10 10,10 0,20 0,30 c

$$$29. Which one of the following is an AutoCAD absolute point coordinate?

$ @361,270

$ 60<90

$$361,270

$ none of the above

$$$30. Absolute coordinates measured are from the-

$$ current UCS origin

$ last point entered

$ lower left hand corner as set by LIMITS command

$ world co-ordinate origin

$$$31.

With reference to the picture above and in particular the angle at the lower right corner. The angle one would key in to draw the line would depend on where the start point was. Which one of the following would NOT produce the required line?

$ 135

$$ -135

$ 225

$ 45

$$$32.

There are four objects on the screen, a Circle, Square, Triangle and Rectangle. Which of these statements describes the object(s) that will be selected using the “crossing” method of selection?

$ the Circle

$$ All but the circle

$ the Rectangle

$ Both the Triangle and the Square

$$$33. There are at least eleven options to the “select objects” prompt. Which of the following has an incorrect option?

$ W WP R

$ C CP F

$ L ALL E

$$ P SI A

$$$34. From which direction does AutoCAD start measuring angles?

$ 12 o'clock
$$ 3 o'clock
$ 6 o'clock
$ 9 o'clock

$$$35. The ‘select object’ option ‘Last” is best described by

$$ Picks the last drawn single object, that is visible on the screen

$ Picks the last drawn single object

$ Picks the last drawn group of objects

$ Picks the last object in a Window or Crossing selection

$$$36.

There are four objects on the screen, a Circle, Square, Triangle and Rectangle. Which of the statements describes the object(s) that will be selected using the “Window” method of selection?

$ the Circle

$ All but the circle

$ the Rectangle

$$ Both the Triangle and the Square

$$$37. The ‘select object’ option ‘Previous” is best described by

$ Picks the single object drawn by previous command

$ Picks the previous drawn single object

$ Picks the previously picked group of objects

$$ Picks the previous object in a Window or Crossing selection

$$$38. What does WCS stand for?

$ Western CAD System
$ Worldwide Coordinate Sectors
$$ World Coordinate System
$ Wrong CAD Settings

$$$39. The array command is useful because with it one can-

$ Save drawing memory

$$ Copy a single object, or a group of objects and make a new and regular group with it/them

$ Make random copies of objects

$ Achieve all the above

$$$40. Which one of the following system variables disables the prompt which asks for attribute values, and causes attributes to be set to their defaults?

$ ATTDIA

$ ATTDISP

$$ ATTPROMPT

$ ATTREQ

$$$ 41. Which one of the following best defines attributes as used in AutoCAD and defined by the command DDATTDEF.

$ Text entities that can link to a database,

$$ Special text entities within a block.

$ Text entities that use an alternative font

$ Special text entities.

$$$42. Attributes MUST

$ be created on layer 0

$ have a numeric value

$$ be attached to a block

$ be visible

$$$43. What is the significance of using the command WBLOCK?

$ WBLOCK only works on blocks,

$$ the block is written to disk and can be used later in other drawings.

$ the block is written to the current drawing file only, saving disk space.

$ the block can have attributes written to it later.

$$$44. The effect of the EXPLODE command when applied to a block is to?

$$ reduce a block to its constituent entities to allow editing.

$ return a block to its created scale and rotation.

$ allow the editing of a block with different X,Y factors.

$ place constituent entities all onto the current layer.

$$$45. The use of blocks allows libraries of standard parts to be developed and saved for latter use. Blocks may be stored -

$$ on disk.

$ on disk, CDROM and the Internet.

$ on disk and CDROM.

$ on disk and the Internet.

$$$46. Which one of the following methods should be used to repeat a complex part in a drawing in order to minimize file size?

$ use the COPY command

$ use the MIRROR command

$use the ARRAY command

$$ create a BLOCK then use INSERT

$$$47. Which one of the following is a correct statement regarding AutoCAD blocks?

$$ Blocks can only be inserted into a drawing if they already exist in that drawing,

$ A block can have no more than ten attributes,

$ The insert command looks first within the drawing for blocks and then to the disk.

$ Every block has to have at least one attribute.

$$$48. The SETVAR command is used to?

$ configure the program settings to suit the various hardware devices

$ configure AutoCAD for use with a tablet menu

$ create an 'object set' for editing

$$ change the values of the system variables

$$$49. If the system variable MIRRTEXT is set to 1, text is

$$ mirrored

$ not mirrored

$ not reproduced in the mirror image

$ mirrored and reversed

$$$50. Which one of the following allows the value of the system variable PICKBOX to be changed whilst in the ERASE command?.

$$ SETVAR pickbox or PICKBOX

$ ‘SETVAR pickbox or ‘PICKBOX

$ SELECT

$ CHANGE

$$$51. Which one of the following system variables determines the visibility of the control points of a plane spline curve?

$$ SPLFRAME

$ SPLMODE

$ SPLINESEGS
$ SPLINEVIEW

$$$52. The system variable SPLINETYPE determines?

$$ whether the 'curve' option of the PEDIT command produces a spline curve or a fit curve

$ whether editing functions are performed on the spline curve or on it's controlling frame

$ the accuracy of approximation of a spline curve

$ whether a spline curve is a quadratic b-spine or cubic b-spline

$$$53.Which one of the following is the setting for the system variable MIRRTEXT to prevent text items being reversed in the mirror image when using the MIRROR command?

$$ 0

$ 1

$ ON

$ OFF

$$$54. Which of the following system variables controls the accuracy of approximation of a spline curve?

$ SPLFRAME

$ SPLINEFIT

$$ SPLINESEGS

$ SPLMODE

$$$55. Which one of the following commands can be used to change the value of a system variable?

$ CHANGE

$ DlMVAR

$ SELECT

$$ SETV A R

$$$56. The effect of setting the system variable SKPOLY to a value of 1 is that-

$ sketched drawings can not be edited.

$$ in sketch mode all subsequent lines are polylines,

$ all components of a sketched line can be edited.

$ subsequent sketched lines are not polylines.

$$$57. What option would be selected following the TEXT command to select a different type of text to that currently in use?

$$ NEW

$ FONT

$ SET

$ STYLE

$$$58. One effect of setting the value of MIRRTEXT=0 is that?

$$ text is displayed but not mirrored

$ text is displayed as a mirror image

$ text is not displayed

$ only text can be mirrored

$$$59. The command to create a filled circle is-

$ Circfill

$ Floodfill

$ Fillcirc

$$ Donut

$$$60. Which one of the following commands CANNOT be undone?

$XREF

$ SETVAR

$$ SAVE

$ LIST

$$$61. Which one of the following commands allows simultaneous pan and zoom?

$$ ZOOM DYNAMIC

$ ZOOM EXTENTS

$ ZOOM CENTER

$ ZOOM PAN

$$$62. The effect of setting FILL to OFF is that -

$$ wide polylines are shown as unfilled lines.

$ wide polylines are shown as a single line between the end specification points

$ TTF fonts are not displayed

$ polylines are not displayed

$$$63. Which one of the following commands reports details of the current limits, defaults, modes and extents?

$ ID

$ LAYER

$ LIST

$$ STATUS

$$$64. Which one of the following is the BEST procedure for drawing a line from the point of intersection of a line and a circle?

$ Select the LINE command and then use 'object snap' with the INS option,

$$ Select the LINE command and then use 'object snap' with the INT option.

$ Set a small SNAP value then select the LINE command and SNAP to the intersection

$ Zoom in on the intersection, then select the LINE command and click the LH mouse button for the start point

$$$65. Which of the following statements is false -

$ The sketch command can draw either lines or splines.

$ The sketch increment will effect the size of the dwg file.

$ The sketch command is used to draw first drafts of drawings to be refined later,

$$ The sketch command is used to draw those parts of a drawing normally drawn freehand.

$$$66.

The 30mm diameter circle in the picture above has to be positioned 30mm from the too edges shown. Which of the following combinations of AutoCAD commands will produce the required results most efficiently

$ Filet 30 then offset by 15

$ Offset each edge by 30 then Circle INT

$$ Set a new UCS on the corner at the correct angle, then CIRCLE 30,30 15

$ Circle TTR 30 then offset by 15

$$$67. The command to create a filled circle is -

$ Circfill

$ Fioodfill

$ Fillclrc

$$ Donut

$$$68. The divide command

$$ divides an object info equal parts

$ places markers along the object

$ uses the current point style set by pdmode

$ all of the above

$$$69. When breaking a circle the break will occur in the

$ anti clockwise direction

$ clockwise direction

$$ horizontal direction

$ shortest direction

$$$70. Which one of the following statements is False?

$$ Plines can be filed but not outlined.

$ Plines can have either a consistent width or varying widths,

$ Plines can be made from lines and arcs.

$ Plines can be smoothed.

$$$71. Which of the following shapes CANNOT be drawn by the polygon command?

$ Square

$ Hexagon

$$ Rectangle

$ Equilateral triangle

$$$72. Which of the following statements is false

$$ An object on a locked layer can not be modified

$ The command "Zoom e" ignores any objects on layers that are turned off

$ The current layer can be turned off

$ The command "Vplayer" allows you to control the layer visibility in different viewports

$$$73. The effect of freezing a layer is to?'

$ make it invisible and prevent regeneration

$ make it invisible but allow regeneration

$ allow visibility and regeneration

$$ display the layer but prevent editing of it

$$$74. In a complex multi-layer drawing, which one of the following commands can be used to improve the efficiency of drawing regeneration during a editing session

$ LAYER followed by FREEZE

$$ LAYER followed by ON

$ LAYER followed by THAW
$ LAYER followed by OFF

$$$75. Which one of the following is the maximum number of layers which can be defined in an AutoCAD drawing?

$ 64

$ 128

$ 256

$$ UNLIMITED

$$$76. Which one of the following commands can be used to obtain information about a selected object?

$ ID

$$ LIST

$ MEASURE

$ STATUS

$$$77. Which of the following statements is false

$$ The Locked or Unlocked slate of a layer has no effect on an objects visibility

$ The command "Zoom e" includes any objects on layers that are turned off

$ It is not possible to change an object on a thawed layer to a frozen layer

$ You can draw on a layer that is in the off state

$$$78. Which of the following statements is false when related to the use of layers in the construction of a drawing.

$$ There is no method of hiding objects in one Paper Space viewport and show the same objects in another viewport.

$ Layers enable you to logically structure the drawing by grouping together related objects on the same layer,

$ Layers allow groups of drawing entities to remain visible, but unaffected by editing commands.

$ Layers allow different colors and line types to be used by assigning colours and line types to

different layers

$$$79. When 'EXTNAMES’ is set to 1, i.e. "uses AutoCAD 2000 parameters" layer names are limited to how many characters in length?

$ Unlimited

$ 128

$$ 255

$ 1000

$$$80. Polar coordinates are used mostly for drawing...?

$ Circles
$ Arcs
$ Vertical lines
$$ Angled lines

$$$81. Why does AutoCAD allow you more than one layout?

$ Different output devices.

$ Different sizes of output.

$ Different output orientation.

$$ All of the above.

$$$82. Which of the following information should be put only on MS (Model Space).

$$ The Drawing, Dimensions, Notes etc.

$ Copyright statements.

$ View Ports, Border with Title, issue, Scale, Date etc.

$ Company Logos.

$$$83. The correct command to make a PS (Paper Space) viewport display at a given scale is:

$ Zoom nXP in MS.

$$ Zoom nXP in PS

$ Zoom nX in MS

$ Zoom nX in PS

$$$84. Тhe required scale factor You can find the Scale of a PS (Paper Space) viewport: using which command -

$ Enquire

$ List

$$ Scale

$ Measure

$$$85. A drawing of a complex building site may show items such as Mobile Crane, Temporary Site Access, Gas Bottle Store etc. The advantage of using a PS layout plot of the drawing is-

$$ Each item can be shown at an appropriate scale.

$ The whole site and the individual items can be shown.

$ Items shown in one viewport can be frozen in another.

$ All of the above.

$$$86. Which of the following information should be put only on PS.

$$ View Ports, Border with Title, Issue, Scale, Date etc.

$ The Drawing, Dimensions, Notes etc.

$ Graphic images,

$ Internet links.

$$$87. A common command for many Windows applications is "Page Setup’. What in AutoCAD does Page Setup achieve?

$$ Sets the scale at which the drawing is printed.

$ Sets the output device, also the size and orientation of the output
$ Sets limits and the working units.

$ Sets Up the paper size, margins and orientation

$$$88. Which one of the following key combinations is a standard windows shortcut that does not relate to the clipboard.

$$ Ctrl + S

$ Crtl + X

$ Ctrl + V

$ Ctrl + C

$$$89. Holding down the [Ctrl] key and pressing the [TAB] key causes which of the following to happen,

$ Switch between open applications.

$ Toggle the Tablet mode.

$$ Switch between open drawings /documents.

$ Move cursor to the next snap/tab position,

$$$90. Which of the following key combinations does not invoke an I/O command?

$ Ctrl + P

$$ Ctrl + F

$ Ctrl + S

$ Ctrl + O

$$$91. Holding down the [Ctrl] key and pressing the F key causes which of the following to happen.

$ Flip between text and graphics screen.

$ Displays the files dialogue,

$$ Displays the "Find Text” dialogue.

$ Moves forwards one page.

$$$92. Ctrl + [Home] and Ctrl + [End] move the cursor in a text application to -

$ a paragraph before or after the current one,

$ either side of the document screen,

$ either end of the current document,

$$ the first or last document in the list of open documents.

$$$93. Holding down the [Alt] key and pressing the [TAB] key causes which of the following to happen.

$$ Switch between open applications.

$ Toggle the Tablet mode.

$ Switch between open drawings/documents.

$ Move cursor to the next snap/tab position.

$$$94. In a Windows dialogue box, moving from one field to another is achieved by which of the following key combinations?

$ Ctrl +[Tab]

$$ Alt +[Tab]

$ Shift + [Tab]

$ [Tab]

$$$95. Which of the following statements is true?

$ Ctrl + S saves the current document and forces an autosave even if the elapsed time is less than the threshold value.

$ Ctrl + S saves the current document using a default filename.

$ There is no difference between Save and Save As.

$$ Windows applications know if the current document has been saved before, so that when a Ctrl + S is issued Windows will determine whether to do a Save or Save As.

$$$96. When constructing an AutoCAD Solid Model the UCS command is used to-

$$ Draw more accurately

$ Draw Solid Objects

$ Rotate Solid Objects

$ Define a new Drawing Plane

$$$97. How many points do you need to define for the rectangle command?

$ One
$$ Two
$ Four
$ None

$$$98. Which keystrokes will UNDO a command

$ Control+U
$ Alt+U
$ Control+Z
$$ Alt+Z

$$$99. When drawing in 2D, what axis do you NOT work with?

$ X
$ Y
$$ Z
$ WCS

$$$100. What should you pay attention to when learning AutoCAD?

$$ The Command Line
$ The Status Bar
$ The Title Bar
$ Tool Icons

$$$101. Which one of these will NOT start the Print command?

$ Typing PLOT
$ Typing PRINT
$ Pressing Control+P
$$ Pressing Alt+P

$$$102. How many snap points does an object have?

$ One
$ Two
$$ Depends upon the object
$ At least four

$$$103. How should you select objects when using the stretch command?

$$ With a crossing window
$ Pick them one by one
$ Hold the shift key while selecting
$ Type 'S'

$$$104.

Which of the following statements describes the best procedure to draw the base of the part shown in the picture above?

$$ BOX then CHAMFER then FILLET.

$ RECTANGLE then FILLET then EXTRUDE,

$ Both (a) and (b) above are possible but (b) is more efficient

$ Both (a) and (b) are equally efficient.

$$$105.

Which of the following statements describes the best procedure to draw the two counter bores at the left end of the base of the part shown in the picture above?

$ Draw the 4 cylinders, UNION all 4 then subtract the result from the main body,

$$ Subtract the 4 cylinders from the main body.

$ Both (a) and (b) above are possible but (b) is more efficient.

$ Both (a) and (b) are equally efficient

$$$106.

Which of the following statements describes the best procedure to draw the single spigot and through hole on the top of the base of the part shown in the picture above?

$$ Draw 2 cylinders, UNION the body and the larger cylinder then SUBTRACT the smaller cylinder from the main body.

$ SUBTRACT the smaller cylinder from the main body then UNI ON the large cylinder and the body.

$ Both (a) and (b) above are possible but (a) is more efficient.

$ Both (a) and (b) are equally efficient

$$$107.

Which of the following statements describes, the best procedure to draw the single spherical dimple on the top ofthe part shown in the picture above?

$$ Draw a circle and REVOLVE it 180 degrees then SUBTRACT the result from
the main body.

$ Draw a SPHERE and SUBTRACT it from the main body.

$ Both (a) and (b) above are possible but (b) is more efficient

$ Both (a) and (b) are equally efficient

$$$108.

Which of the following statements describes the best procedure to draw the conical base that is below the hexagonal structure of the part shown in the picture above?

$$ Draw a circle then extrude it, stating the angle.

$ Draw half the cross section as a pline and REVOLVE it 360 degrees,

$ Both (a) and (b) above are possible but (a) is more efficient.

$ Both (a) and (b) have their merits; if the angle is known then (a) is better, If the top diameter is important then (b) is better.

$$$109.

Which of the following statements describes the best procedure to draw the pencil like structure of the part shown in the picture above?

$$ Draw a hexagon then extrude it. Draw a cone and UN ION the cone and hexagon together.

$ Draw a hexagon then extrude it. Draw "a triangular pline then REVOLVE it 360 degrees. SUBTRACT the result from the hexagon.

$ Both (a) and (b) above are possible but (b) is more efficient

$ Both (a) and (b) are equally efficient.

$$$110. Which one of the following is the AutoCAD filename extension used to indicate a compiled text font?

$ HDX

$ SHP
$$ SHX

$TXT

$$$111. Which one of the following could be an AutoCad drawing file?

$ DWG.PLAN

$$ PLAN.DWG

$ DRAW.FLE

$ FILE, TXT

$$$112. The line types definitions ore stored on the system with an extension of?

$.LTT

$.LSP

$$.LIN

$ LAT

$$$113. Which one of the following key combinations is a standard windows short cut that does not relate to the clipboard, '

$$ Ctrl + S

$ Crtl + X

$ Ctrl + v

$ Ctrl + C

$$$114. The shortcuts or command alias that allows us to key in L and AutoCAD responds with LINE are stored in a file named

$ SHORT-CUT.TXT

$ ACAD.COM
$$ ACAD.PGP
$ ACAO.EXE

$$$115. Which of the following key combinations issues the ISOPLANE command?

$CONTROL and T or F4

$$ CONTROL and E or F5

$ CONTROL and D or F6

$ CONTROL and I orF7

$$$116. Which of the following statements is true?

$ Backup copies of drawing files are saved in the "Support" folder.

$ Backup copies of drawing files are saved in a folder set by the user.

$$ When a drawing is initially saved a backup copy is made with a.BAK extension. This can be renamed as a.DWG at a later date.

$ When a drawing is saved for the second time a backup copy is made with a.BAK extension. This can be renamed as a.DWG at a later date.

$$$117. Which one of the following key combinations will toggle SNAP?

$ Either F7 or CONTROL and G

$ Either F6 or CONTROL and D

$$ Either F9 or CONTROL and B

$ Either F8 or CONTROL and O

$$$118. Which one of the following key combinations will toggle COORDS?

$ Either F7 or CONTROL and G

$$ Either F6 or CONTROL and D

$ Either F9 or CONTROL and B

$ Either F8 or CONTROL and O

$$$119. Which one of the following best describes a 'user coordinate System?

$$ The pair of coordinate points which define the lower left and upper right corners of the drawing boundary

$ A series of coordinate points stored as variables for later use in the drawing

$ A coordinate system whose origin is located anywhere in three dimensional space

$ The master datum: from which all measurements are taken.

$$$120. Absolute coordinates are measured from the -

$$ current UCS origin.

$ last point entered,

$ lower left hand corner as set by LIMITS command.

$ world co ordinate origin.

$$$121. The positron of a mouse on a surface is NOT directly related to the position of the screen cursor. This makes the mouse unsuitable for -

$$ Selecting two points on the screen for a line draw operation.

$ Tracing an existing drawing,

$ Selecting menu items on the screen.

$ Sketching.

$$$122. Which one of the following is an AutoCAD absolute point coordinate?

$ ©361,270

$ 60<90
$$ 361,270

$ None of the above

$$$123. When drawing a digital watch measuring 30mm x 25mm, which one of the following would be the BEST set of drawing limits to use?

$ 0,0/40,35

$$ 0,0/30,25

$ 0,0/100,100

$ 0,0/297,210

$$$124. To continue drawing a line from the last known point, enter?

$ 0,0

$$ @

$ Next

$ a or b

$$$125. By default, AutoCAD has the following workspaces

$ 2D Drafting & Annotation

$ 3D Modeling

$ My workspace

$$ AutoCAD Classic

$$$126. Which Key do you press to cycle through the available snap points.

$ Ctrl

$$ Shift

$ Tab

$ Alt

$$$127. One of the below options is wrong about type of Autocad drawing units.

$ Architectural

$ Engineering

$ Decimal

$$ Millimeter

$$$128. Object snap tracking works in combination with object snaps to enable you to temporarily acquire and track up to how many points?

$ One

$$ Two

$ Five

$ Seven

$$$129. The following settings can be made for polar tracking

$ Increment angle

$ Additional angles

$$ Track using all polar angles settings

$ All the answers are correct

$$$129. With a hot grip you can perform these editing tasks

$$ Move

$ Offset

$ Rotate

$ Scale

$$$130. Inorder to Move an object

$$ select a base point, followed by a point to define where the object is moving to.

$ use the Displacement option

$ Select object for grips, then move

$ Above all

$$$131. Copy command also creates Multiples copies of an object

$ True

$$ False

$ creates copies of documents

$ All the answers are correct

$$$132.

What is the angle that you use to rotate the chair from point A to point B

$$ 90

$ -90

$ -270

$ None

$$$133. If you need the text to be reversed, when you mirror the text, then you need to set

$ MIRRTEXT to 0

$$ MIRRTEXT to 1

$TEXTMIRR to 0

$ TEXTMIRR to 1

$$$134. Inorder to get the below result using Object A, you have to set the number of rows and columns to:

$ 4,1

$$ 4,2

$ 4,3

$ 4,4

$$$135. When using copy with grips, select Copy after you have selected an option, such as Move, Mirror, Rotate, Scale, or Stretch.

$ True

$$ False

$ creates copies of documents

$ All the answers are correct

$$$136. By selecting one of the following, the Objects on the layer are not visible and are not considered when the drawing is regenerated.

$$When you off the layer

$When you froze the layer

$When you lock the layer

$None

$$$137. When you use the Match Properties command, you can select multiple source objects

$ True

$$ False

$ You cannot select

$ All the answers are correct

$$$138. Using object snaps to select points for Inquiry commands is Critical

$True

$$ False

$ You cannot select

$ All the answers are correct

$$$139. What happens if you fillet these two lines with radius 0

$$ Cannot fillet

$ sharp corner

$ None

$ All the answers are correct

$$$140. Which of the following can be joined using Join command

$$ A

$ B

$ C

$ D

$$$141. The following are some of the properties and settings that you can save in a layout, except

$ Plot scale

$ Paper size

$$ line weight

$ Drawing orientation

$$$142. You can set viewport scale factor by

$typing vscale

$ typing vpscale

$$ typing viewportscale

$ None

$$$143. What happens when you set VPROTATEASSOC System Variable to 0

$$ When a viewport is rotated, the view inside is not rotated

$ When a viewport is rotated, the view inside is rotated to match the rotation of the
viewport.

$ All the answers are not correct

$ All the answers are correct

$$$144. With the Multiline Text editor, you can do all of the following, except:

$ insert numbered and bulleted lists

$ insert specific drafting and engineering symbols

$$ insert pictures

$ Create Fields such as date, time and author.

$$$145. If you copy and paste text from another drawing or insert a block into a drawing that has the same Text Style name with different properties, the text properties of the host drawing will take precedence

$$ True

$ False

$ All the answers are not correct

$ All the answers are correct

$$$146.

What is the command used to draw the above dimension line?

$ Dimjogged

$$ Dimjogline

$ joggedline

$ Joggeddim

$$$147. If you modify a dimension style, all dimensions using that style in the drawing update
automatically.

$$ True

$ False

$ All the answers are not correct

$ All the answers are correct

$$$148.

The multileaders 4,8,9 represent:

$ Aligned Multileaders

$ Vertical Multileaders

$$ Collected Multileaders

$ Horizontal Multileaders

$$$149.

What type of Island detection type is this?

$ Inner

$ Outer

$ Ignore

$$ Normal

$$$150. Using Purge command we can purge referenced blocks.

$$ True

$ False

$ All the answers are not correct

$ All the answers are correct

$$$151. When you Explode a block, the geometry returns to its original properties.

$$ True

$ False

$ All the answers are not correct

$ All the answers are correct

$$$152. Options used to draw this polyline;

$$ line

$ arc

$ amper

$ width

$$$153. You cannot fillet or chamfer the first segment of a polyline with the last segment of the same polyline.

$$ True

$ False

$ All the answers are not correct

$ All the answers are correct

$$$154. What is the name qiven to the toolbar that has the Eraser included?

$ Draw

$$ Modify

$ Zoom

$ Menu

$$$155. What is the name given to the toolbar that has the Line Command included?

$ Modify

$$ Draw

$ Zoom

$ Menu

$$$ 156.What is AutoCAD?
$$ Graphic Editor
$ Spreadsheet
$ Database
$ Text Editor

$$$ 157. The template of drawing document stored in a file format:
$$. Dwt
$. Dxf
$. Dwg
$. Dws

$$$ 158. Through which menu you can set the paper size?
$$ Format drop-down menu
$ Expands Tools
$ Expands to the View menu
$ Context Menu

$$$159. How many ways to build an arc exists in the AutoCAD?
$$ 11
$ 10
$ 1
$ 6

$$$160. What way to build the arc is the default?
$$ The option - 3 points;
$ The options- start, center, end;
$ The options - beginning, the center, the angle;
$ The option - to continue.

$$$161. UCS – is the abbreviation of the coordinate system:
$$ User
$ Rectangular
$ Derivative
$ World

$$$162. With the help of some options of command "array" you can do?
$$ A rectangular array
$ Circular array
$ Polar tracking
$ Object Tracking

$$$ 163. Command value "Block" in the AutoCAD?
$$ The ability to create libraries of graphics elements for subsequent insertion.
$ Editing an object
$ Scaling an object
$ Creating a database

$$$164. For which graphics primitives the command "Cut" is not applicable?
$$ To lock objects
$ For the circle
$ For a segment
$ For a spline

$$$ 165. The Chamfer command is used to?
$$ Trims two intersecting lines at a given distance from the intersection point and closes the truncated part.
$ Allows you to pair the two segments of a given radius
$ Expands the selected area of ​​the object
$ Removes

$$$ 167. How many ways to create a circle in AutoCAD?
$$ 6
$ 3
$ 9
$ 10

$$$168. Object Snaps to the intersection of objects:
$$ Intersections
$ Endpoint
$ Centre
$ Nearest

$$$ 169. To create a circle by default in AutoCAD?
$$ Using the center
$ A diameter
$ Three points
$ KKK

$$$170.The function "Copy" command?
$$ to create a copy of the selected objects
$ Move the selected object
$ Building array.
$ Stretch selected objects

$$$ 171. Is it possible to set the color of the newly created entities?
$$Yes
$ Only when you run the "Solids";
$ Only when you run the "segment";
$ Only when you run the "Freeform".

$$$ 172. Is the polyline command allows to create arc with a given radius?
$$Yes
$ Yes, the option «off»
$ Yes, with option "?"
$ Yes, the option «on»

$$$ 173. In which panel is located a command to create a spiral (helical)
$$ Drawing
$ Modeling
$ Network
$ Edit

$$$ 174. Is the step grid of "Display Grid" command always equals the value of the resolution specified in the "Snap" command?
$$ Does not always
$ Always.
$ Depend on the parameters of the coordinate counter
$ Depend on the resolution of your monitor

$$$ 175. Does a grid displays on the plotter and printer?
$$ Is not displays
$ displays only on the printer
$ Displays only on the plotter
$ If enabled

$$$ 176.In which tab is "Sources of Light" panel?
$$ Visualization
$ Home
$ View
$ Annotation

$$$ 177. What is the width in "Polyline" command by default?
$$ 0
$ 3
$ 4
$ 0.5

$$$ 178.What area can be hatched by using the Hatch command?
$$ A closed area
$ Not an enclosed area
$ Adjoins area
$ All of

$$$ 179. Is it possible to insert the block being edited from the block list by Paste command?
$$Yes
$ No
$ Only in the case of option "?"
$ Only in the case of options "in"

$$$ 180. What angle of rotation by default with Paste command?
$$ 0
$ 90
$ 180
$ 45

$$$181. Object Snaps to the midpoint of the line or segments:
$$ Mid
$ Endpoint
$ Tangent
$ Continued

$$$ 182. Which command will automatically draw a line segment connecting the last segment with the specified point and point of the first segment?
$$ Close
$ Cancel
$ No such command
$ Repeat

$$$ 183. Undo the last executed command?
$$ Cancel;
$ Repeat;
$ Cteret;
$ Regenerate.

$$$184. How to view a list of all types of library line in the “Types of line " command?
$$ Menu Format - Types of line;
$ Menu Format - Line weight;
$ Menu Format - Layers;
$ Menu Format - Styles multiline.

$$$185. What is the function of the "List scale" command?
$$ Change the drawing scale coefficient;
$ Change linetype
$ Create a new type of lines
$ Copying lines

$$$186. Object Snaps to the end point of the line or segments:
$$ Endpoint
$Mid
$ Tangent
$ Continued

$$$ 187. What does the mirror command?
$$ Creates symmetrical image of objects relative to the defined axis of symmetry.
$ Copies the selected object
$ Moves the selected object
$ Change line color

$$$ 188. How mach number of objects can be moved with the transfer command?
$$ all selected objects.
$ Only one object
$ Only five objects.
$ Only two objects

$$$ 189. What is the number of rows and columns by default when you run the Array?
$$ 4 rows, 4 columns
$ 1 columns, 2 rows
$ 2 columns, 2 rows
$ 2 rows, 1 columns

$$$ 190. How lines are drawn, if the option is set ON in "ORTHO mode" command?
$$ Only parallel to axes, either horizontally or vertically
$ At any angle to the coordinate axes
$ Only parallel to the X
$ Only 45 degrees

$$$ 191. Pan command function?
$$ Move the current view of the display window around the drawing.
$ Increasing the drawing area.
$ Reduce the drawing area
$ Transfer Object

$$$192. What is the first and second chamfer distance by default?
$$ 0
$ 5
$ 9
$ 8

$$$ 193. How to get out of text mode after typing in the text command?
$$ Double-click on the Enter key
$ Keyboard combination Ctrl + C
$ Select from the menu screen, click AutoCAD and click the left mouse button
$ Keyboard combination Ctrl + V

$$$ 194. Which panel is used to control colors, types and thickness?
$$ Properties
$ Clipboard
$ This panel does not exist
$ Sizes

$$$ 195. To create a drawing layers we use the control panel...
$$ Layers
$ Properties
$ Subobject
$ View

$$$ 196. What makes "frozen" layer?
$$ Making layers invisible and saves time in the regeneration of the drawing
$ Level objects are removed from the drawing
$ Object-level protection from accidental deletion
$ Block object

$$$197. On what peripheral can be derived hard copy of drawing file AutoCAD?
$$ On any printer
$ Only for matrix printers
$ Only on laser printers
$ Only on inkjet printers

$$$ 197. Squeezing the 2D object by normal or by the path is executed with the command...
$$ Roll
$ Siphon
$ Extrude faces
$ Smoothing object

$$$ 198. The command "Split" allows to:
$$ Partition object into segments
$ Changes the orientation of objects by their rotation around the base point
$ Mark again objects to another location
$ Cuts the selected object

$$$ 199. How to set the correct thickness of the polyline?
$$ Use the option "width";
$ Use the command - arch;
$Use the command - length;
$ Use the command - cancel

$$$200. With what command you can insert into a drawing already created geometry, from the block list?
$$ Box
$ Circular array
$ Likeness
$ Cut

$$$ 201. How to quickly build an octagon in AutoCAD?
$$ By using the polygon;
$ With the option multiline;
$ Using the unit;
$ Using the segment;

$$$ 202. Changing the size of the sight?
$$ Tools-Options-Select;
$ Edit-Paste;
$ Format - Limits;
$ View - Tools;

$$$203. How to change the color of the screen?
$$ Tools - Settings - Display - Color
$ Edit - Paste
$ Format - Limits
$ View - Tools

$$$ 204. Assigning extrusion command:
$$ Extrude the selected area
$ Move the body
$ Rotation of one or more faces
$ Color change of faces

$$$ 205. In what menu you can change the style points?
$$ Format
$ File
$ Edit
$ Edit

$$$206. Function of Zoom command-
$$ to increase and decrease of the drawing area
$ Copying objects
$ Move Object
$ Change object properties

$$$ 207. To disable the layer is?
$$ Making layers invisible
$ Blocking layer
$ Object-level protection from accidental deletion
$ Making levels unseen and saves time when drawing regeneration

$$$ 208. To blocking layer is?
$$ Blocking layer
$ Object-level protection from accidental deletion
$ Making levels unseen
$ Level objects are removed from the drawing

$$$ 209. Is it impossible to assign to layer a color?
$$Yes, it is
$ No
$ Yes, with option "?"
$ Yes, the option «on»

$$$ 210. Which panel is the zoom of the drawing primitives?
$$ Quick-All
$ Navigation-frame
$ Quick-Zoom
$ Navigation-Object

$$$ 211. What binding mode sets to a lengthening of the interval?
$$ Continued
$ Intersection
$Mid
$ Centre

$$$ 212. Which command draw a line without end or beginning?
$$ Direct
$ Segment
$ Beam
$ Polyline

$$$213. Is it possible to construct a polyline with different values ​​of start and end thickness?
$$ Yes, for any type of segment
$ Yes, but only for a line segment
$ No
$ Yes, but only for the arc segment

$$$ 214. From which menu is called multiline styles?
$$ Format
$ View
$ Draw
$ Service

$$$215. Which command allows to unit objects
$$ Combining
$ Subtract
$ Intersection
$ Smoothing

$$$ 216. From what drop-down menu it is possible to set measurement units?
$$ Format
$ Service
$ View
$ Draw

$$$ 217. Which command allows you to draw a donut?
$$ donut
$ Circle
$ Spiral
$ Doug

$$$ 218. How many ways to create a text in the program AutoCAD?
$$ Two
$ Three
$ Four
$ Five

$$$ 219. Which function key is enabled to establish an orthogonal mode?
$$ F8
$ F1
$ F6
$ F3

$$$220.In which tab is the "Edit" panel?
$$ Main
$ Network Modeling
$ Visualization
$ Annotation

$$$ 221. How many types of arrays in AutoCAD?
$$ Two
$ Three
$Five
$Four

$$$222. How many objects can simultaneously participate in the command "offset"?
$$ 1
$ 2
$ 3
$5

$$$ 223. Surfaces, consisting of pieces of Bezier and originally created as fragments of the plane rectangular?
$$ Patch Grids
$ Particle Systems
$ Extended Primitives
$ Editable Spline

$$$ 224. Specific type of standard objects, which makes to easy simulate two types of mechanical devices: the springs and dampers?
$$ Dynamics Objects
$ Doors (Doors) and Windows (Windows)
$ Patch Grids
$ NURBS Surfaces

$$$ 225. Variety of standard objects, which allows to easily simulate these rather complex architectural elements, such as doors and windows of various types?
$ Dynamics Objects
$$ Doors (Doors) and Windows (Windows)
$ Patch Grids
$ NURBS Surfaces

$$$ 226. This category includes various types of lines that forms a disconnect or closed two-dimensional figures
$$ The objects of category Shapes
$ The objects of category Geometry
$ The objects of category Lights and Cameras
$ The objects of category Helpers

$$$ 227. Standard two-dimensional geometric shapes, such as rectangle, ellipse, star, lines of arbitrary curvature and contours of text characters?
$$ Splines
$ NURBS Curves
$ Geometric / Deformable
$ Patch Grids

$$$ 228. Variety of lines, allowing to build a smooth, no break point?
$ Splines
$$ NURBS Curves
$ Geometric / Deformable
$ Patch Grids

$$$ 229. This category includes objects, that are not included in the final image of scene and are designed to their simplify modeling or animation.?
$ Category Shapes
$ The objects of Geometry
$ Categories Lights and Cameras
$$ The objects Helpers

$$$ 230. Objects used as an aid in the design and animation of geometric patterns?
$$ Standard
$ CameraMatch
$ VRML 1.0/VRBL and VRML97
$ Atmospheric Apparatus

$$$231. Objects designed for the localization of manifestation of environment effects?
$ Standard
$ CameraMatch
$ VRML 1.0/VRBL and VRML97
$$ Atmospheric Apparatus

$$$ 232. Objects used in the simulation of three-dimensional scenes, intended for export to the description languages of virtual reality.?
$ Standard
$ CameraMatch
$$ VRML 1.0/VRBL and VRML97
$ Atmospheric Apparatus

$$$233. This category includes facilities designed to simulate the effects of various forces on geometric models or particles that fall under the influence of the "force field."
$ The objects of category Shapes
$ The objects of category Geometry
$ The objects of category Lights and Cameras
$$ The objects of category Space Warps

$$$ 234. Variously deformed geometric models of objects?
$$ Geometric / Deformable and Modifier-Based
$ Particles & Dynamics and Particles Only
$ Dynamics Interface
$ Particles Only

$$$ 235. Exerts a force on the individual particles in particle systems, and are used to simulate the action of gravity on objects or wind?
$ Geometric / Deformable and Modifier-Based
$$ Particles & Dynamics and Particles Only
$ Dynamics Interface
$ Particles Only

$$$ 236. What are used to provide impact on dynamic systems?
$ Geometric / Deformable and Modifier-Based
$ Particles & Dynamics and Particles Only
$$ Dynamics Interface
$ Particles Only

$$$ 237. Each type of system is a collection of related objects, that provide an animation of system?
$$ The objects of category Systems
$ The objects of category Geometry
$ The objects of category Lights and Cameras
$ The objects of category Space Warps

$$$ 238. A system that allows you to create a set from a given number of objects, orderly arranged in a circle of the specified radius and animate motion of these objects?
$ Bones
$$ Ring Array
$ Sunlight
$ Spline

$$$ 239. A system that allows to create a source of parallel rays of light, simulating sunlight, and play movement of the sun according to the geographical location, time of year and day of the simulated scene?
$ Bones
$ Ring Array
$$ Sunlight
$ Spline

$$$ 240. Objects of this type are spline curves that do not have the characteristic parameters that allow modification.
$$ Editable Spline
$ Patch Grids
$ Particle Systems
$ Extended Primitives

$$$ 241. The objects of this type include 3D geometric models of the bodies represented by the shell meshes with triangular or quadrangular cells and not having the characteristic that allow modification.
$$ Editable Mesh
$ Editable Spline
$ Patch Grids
$ Particle Systems

$$$ 242. Objects of this type can be created based on the parametric objects of Geometry, except of the Particle Systems and NURBS Surfaces.
$$ Editable Patch
$ Editable Mesh
$ Editable Spline
$ Patch Grids

$$$ 243. Menu, which allows you to apply different transformations to the objects, and to provide a challenge floating palettes and command dialogs of Material Editor and Material / Map Browser?
$$ Tools (Service)
$ Menu Rendering
$ Menu Group
$ Menu Views

$$$ 244. This menu allows you to create, edit, and destroy the named groups of objects?
$ Tools
$ Menu Rendering
$$ Menu Group
$ Menu Views

$$$245. The action of the object: moving, rotating, scaling?
$$ Transformation
$ Format
$ Deformation
$ Morphing

$$$ 246. Sub-Object is?
$$ A component of the object
$ Editable surface
$ Line
$ Segments

$$$ 247. The set of surface parameters that define the appearance of the object when rendering?
$$ Material
$ Lighting
$ Display level
$ Scroll

$$$ 248. Component material, the image superimposed on one of the channels of the material?
$$ Texture / Map
$ Figure
$ Layer
$ Surface

$$$ 249. The line connecting two vertices?
$$ Edge
$ Segment
$ Polygon
$ Spline

$$$ 250. In 3-dimensional computer graphics all objects are usually represented as
$$ Set of surfaces or particles.
$ Primitives
$ Individual objects
$ Points

$$$ 251. Function "Copy"?
$$ Create a copy of the selected objects
$ Move the selected object
$ Building array.
$ Stretch selected objects

$$$ 252. Types of windows:
$ Sliding, Pivoted, Awning
$ Casement, Projected
$ Fixed
$$ All answers are true

$$$ 253. How many types of stairs can be created in 3ds max?
$$ 4
$ 5
$ 6
$ 3

$$$ 254. Types of stairs:
$ L-Type, Straight
$ Spiral
$ U-Type
$$ All answers are true

$$$ 255. For what stairs indicats additional Radius?
$$ Spiral
$ L-shaped
$ Direct
$ U-shaped

$$$ 256. What action shown in the picture?

$$ Rotate
$ Move an object in the plane YZ
$ Scale
$ Move

$$$ 257. What action shown in the picture?

$$ Move the object in the YZ plane
$ Rotate an object
$ Scale
$ Move

$$$ 258. What action shown in the picture?


$$ Scaling an object
$ Move an object in the plane YZ
$ Rotate an object
$ Move

$$$ 259. To align one object relative to another, you need to select the first object, the command -
$$ Tools> Align and click on the second object
$ Edit> Clone
$ Instance
$ Click on the object and drag

$$$ 260. What shortcut keys use for Clone Objects?

$$ Ctrl + V
$ Ctrl +7
$ Ctrl +8
$ Ctrl + M

$$$ 261. Created samples of models are stored in the?
$$ Library
$ Keyboard
$ Web
$ Map

$$$ 262. What tool of control the animation keys allow you to move along the timeline, leaving unchanged the intervals between them, and their numerical values?
$$ Move keys
$ Slide keys
$ Skale keys
$ Add keys

$$$ 263. What method allows you to add the effect "blurring" of the fast-moving objects?
$$ Motion blur
$ Duration
$ Samples
$ Duration subdivision

$$$ 264. Which filter in rollout Lens effects Parameters helps to create shine object?
$$ Glow
$ Swirl
$ Wave
$ Gradient

$$$ 265. Which command allows you to copy an object?
$$ Clon
$ Fix
$ Scale
$ Select

$$$ 266. What type of object to animate precipitation like rain?
$$ Spray
$ PArray
$ PCloud
$ Snow

$$$ 267. The smallest structural unit of an object, point in 3D space?
$$ Vertex
$ Pivot Point
$ Gizmo
$ Border

$$$ 268. In the polygonal object it is a group of open edges?
$ Border
$$ Gizmo
$ Pivot Point
$ Vertex

$$$ 269. How to add an additional attribute to any object as shown in the figure (or whatever)?

$ Using the Parameter Wire Dialog.
$$ Using the Parameter Editor.
$ Using the Parameter Collector.
$ Using the Curve Editor.

$$$ 270. How to move the viewport while drawing / creating a spline?
$$ Press the "I".
$ Use the arrow keys / cursors.
$ Middle mouse button.
$ Press the Alt key and make your cursor over the viewport border.

$$$ 271. Procedural map that lets you use to describe the characteristics of the material in any graphic format in 3ds max (TIFF, JPEG, GIF, etc.)
$$ Bitmap
$ Cellular
$ Checker
$ Composite

$$$ 272. Procedural map, that generates the structure of the material, which consists of cells. Most often, such a structure is used in the creation of organic structures, in particular, the modeling of the skin
$$ Cellular
$ Falloff
$ Bitmap
$ Composite

Поиск по сайту: