АвтоАвтоматизацияАрхитектураАстрономияАудитБиологияБухгалтерияВоенное делоГенетикаГеографияГеологияГосударствоДомДругоеЖурналистика и СМИИзобретательствоИностранные языкиИнформатикаИскусствоИсторияКомпьютерыКулинарияКультураЛексикологияЛитератураЛогикаМаркетингМатематикаМашиностроениеМедицинаМенеджментМеталлы и СваркаМеханикаМузыкаНаселениеОбразованиеОхрана безопасности жизниОхрана ТрудаПедагогикаПолитикаПравоПриборостроениеПрограммированиеПроизводствоПромышленностьПсихологияРадиоРегилияСвязьСоциологияСпортСтандартизацияСтроительствоТехнологииТорговляТуризмФизикаФизиологияФилософияФинансыХимияХозяйствоЦеннообразованиеЧерчениеЭкологияЭконометрикаЭкономикаЭлектроникаЮриспунденкция

Question 6. When running OSPF, what would cause router A not to form an adjacency with router B?

Читайте также:
  1. Answer the following questions.
  2. Answer the following questions.
  3. Answer the question: What is the main task of criminal law?
  4. Answer the questions
  5. Answer the questions in the written form.
  6. Answer the questions to check your reading comprehension.
  7. Answer the questions.
  8. Answer these questions.
  9. Answer these questions.
  10. B. Match the questions from part A with the answers (ATTENTION: the answers are given from the point of view of American legislation).
  11. CHAPTER 11. QUESTION TAGS, SHORT QUESTIONS, ECHO-QUESTIONS AND SHORT ANSWERS
  12. CHAPTER 6. ANSWERS TO YES/NO QUESTIONS

When running OSPF, what would cause router A not to form an adjacency with router B?

A. The loopback addresses are on different subnets.
B. The values of the dead timers on the routers are different.
C. Route summarization is enabled on both routers.
D. The process identifier on router A is different than the process identifier on router

Answer: B

Explanation

To form an adjacency (become neighbor), router A & B must have the same Hello interval, Dead interval and AREA number.

 

CCNA EIGRP Questions

 

Question 1

A network administrator is troubleshooting an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information?

A. Router# show ip eigrp adjacency
B. Router# show ip eigrp topology
C. Router#show ip eigrp interfaces
D. Router#show ip eigrp neighbors

 

Answer: D


1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 |

Поиск по сайту:

Все материалы представленные на сайте исключительно с целью ознакомления читателями и не преследуют коммерческих целей или нарушение авторских прав. Студалл.Орг (0.003 сек.)