 |
АвтоАвтоматизацияАрхитектураАстрономияАудитБиологияБухгалтерияВоенное делоГенетикаГеографияГеологияГосударствоДомДругоеЖурналистика и СМИИзобретательствоИностранные языкиИнформатикаИскусствоИсторияКомпьютерыКулинарияКультураЛексикологияЛитератураЛогикаМаркетингМатематикаМашиностроениеМедицинаМенеджментМеталлы и СваркаМеханикаМузыкаНаселениеОбразованиеОхрана безопасности жизниОхрана ТрудаПедагогикаПолитикаПравоПриборостроениеПрограммированиеПроизводствоПромышленностьПсихологияРадиоРегилияСвязьСоциологияСпортСтандартизацияСтроительствоТехнологииТорговляТуризмФизикаФизиологияФилософияФинансыХимияХозяйствоЦеннообразованиеЧерчениеЭкологияЭконометрикаЭкономикаЭлектроникаЮриспунденкция
Open the PT Activity.How long will a user be blocked if the user exceeds the maximum allowed number of unsuccessful login attempts:3 minutes
Open the PT Activity 
. Perform the tasks in the activity instructions and then answer the question or complete the task.How does PC0 obtain its IP address: The address was obtained from a DHCP server
Open the PT Activity . Perform the tasks in the activity instructions and then answer the question or complete the task.Which interfaces in each router are active and operational: R1: G0/0 and S0/0/0.R2: G0/1 and S0/0/0
Open the PT Activity . Perform the tasks in the activity instructions and then answer the question or complete the task.What is the application layer service being requested from Server0 by PC0: HTTPS
Open the PT Activity . Perform the tasks in the activity instructions and then answer the question or complete the task.Which protocol is being used on PC_1 to retrieve email messages from the email server: POP3
Place the recommended steps for worm attack mitigation in the correct order. (Not all options are used.): 1Containment;2 Inoculation;3 Quarantine;4 Treatment
Question as presented.Place the options in the following order:end device address; - not scored -; authoritative name server;canonical name;mail exchange record
Question as presented: 
Place the options in the following order: a message that is used to identify the explicit server and lease offer to accept;a message that is used to locate any available DHCP server on a network; - not scored -; a message that is used to suggest a lease to a client;a message that is used to acknowledge that the lease is successful
Question as presented: 
Place the options in the following order:[+] no dedicated server is required; [+] client and server roles are set on a per request basis; [#] requires a specific user interface; [#] a background service is required
Open the PT Activity.Perform the tasks in the activity instructions and then answer the question.Which PC or PCs are sending FTP packets to the server?PC_2
Question as presented: 
Place the options in the following order:- not scored - 192.168.1.64/27 - not scored - 192.168.1.32/27 192.168.1.96/27
Question as presented. Place the options in the following order:- not scored - Network C - not scored - Network A Network D Network B
Open the PT Activity.Perform the tasks in the activity instructions and then answer the question.
Refer to the exhibit. A company is deploying an IPv6 addressing scheme for its network. The company design document indicates that the subnet portion of the IPv6 addresses is used for the new hierarchical network design, with the s ite subsection to represent multiple geographical sites of the company, the s ub-site section to represent multiple campuses at each site, and the s ubnet section to indicate each network segment separated by routers. With such a scheme, what is the maximum number of subnets achieved per sub-site: 16
Refer to the exhibit. A network administrator is configuring access control to switch SW1. If the administrator uses Telnet to connect to the switch, which password is needed to access user EXEC mode: linevtyin
Refer to the exhibit. A ping to PC3 is issued from PC0, PC1, and PC2 in this exact order. Which MAC addresses will be contained in the S1 MAC address table that is associated with the Fa0/1 port: just PC0 and PC1 MAC addresses
Refer to the exhibit. A switch was configured as shown. A ping to the default gateway was issued, but the ping was not successful. Other switches in the same network can ping this gateway. What is a possible reason for this: The no shutdown command was not issued for VLAN 1.
While trying to solve a network issue, a technician made multiple changes to the current router configuration file. The changes did not solve the problem and were not saved. What action can the technician take to discard the changes and work with the file in NVRAM: Issue the reload command without saving the running configuration.
Why is it important to configure a hostname on a device: to identify the device during remote access (SSH or telnet)
Which procedure is used to access a Cisco 2960 switch when performing an initial configuration in a secure environment: Use the console port to locally access the switch from a serial or USB interface of the PC.
What criterion must be followed in the design of an IPv4 addressing scheme for end devices: Each IP address must be unique within the local network.
A network administrator needs to keep the user ID, password, and session contents private when establishing remote CLI connectivity with a switch to manage it. Which access method should be chosen: SSH
Which interface allows remote management of a Layer 2 switch: the switch virtual interface
What is a result of using the service password-encryption command on a Cisco network device: All passwords in the configuration are not shown in clear text when viewing the configuration.
Match the difinitions to their respective CLI hot keys and shortcuts: Tab ->Completes abbreviated commands and parameters;Ctrl-R ->returns directly to the privileged EXEC mode
Up Arrow ->scrolls backwards through previously entered commands;Ctrl-Z ->cancels any command currently being entered and returns directly to privileged EXEC mode;Ctrl-C ->Redisplays, on a new line, the command currently being typed
Refer to the exhibit. An administrator is trying to troubleshoot connectivity between PC1 and PC2 and uses the tracert command from PC1 to do it. Based on the displayed output, where should the administrator begin troubleshooting:R1
Refer to the exhibit. Baseline documentation for a small company had ping round trip time statistics of 36/97/132 between hosts H1 and H3. Today the network administrator checked connectivity by pinging between hosts H1 and H3 that resulted in a round trip time of 1458/2390/6066. What does this indicate to the network administrator:Something is causing a time delay between the networks.
Refer to the exhibit. Consider the IP address configuration shown from PC1. What is a description of the default gateway address:It is the IP address of the Router1 interface that connects the PC1 LAN to Router1
Refer to the exhibit. Consider the IP address configuration shown from PC1. What is a description of the default gateway address: It is the IP address of the Router1 interface that connects the PC1 LAN to Router1
Refer to the exhibit. Host_A is preparing to send data to Server_B. How will Host_A address the packets and frames that will carry this data:The packet destination will be addressed with the IP address of Server_B.*The frame destination will be addressed with the MAC address of the Router_A LAN interface.
Refer to the exhibit. One end of the cable is terminated as displayed, and the other end is terminated in accordance with the T568A standard. What type of cable would be created in this manner: straight-through
Поиск по сайту: