АвтоАвтоматизацияАрхитектураАстрономияАудитБиологияБухгалтерияВоенное делоГенетикаГеографияГеологияГосударствоДомДругоеЖурналистика и СМИИзобретательствоИностранные языкиИнформатикаИскусствоИсторияКомпьютерыКулинарияКультураЛексикологияЛитератураЛогикаМаркетингМатематикаМашиностроениеМедицинаМенеджментМеталлы и СваркаМеханикаМузыкаНаселениеОбразованиеОхрана безопасности жизниОхрана ТрудаПедагогикаПолитикаПравоПриборостроениеПрограммированиеПроизводствоПромышленностьПсихологияРадиоРегилияСвязьСоциологияСпортСтандартизацияСтроительствоТехнологииТорговляТуризмФизикаФизиологияФилософияФинансыХимияХозяйствоЦеннообразованиеЧерчениеЭкологияЭконометрикаЭкономикаЭлектроникаЮриспунденкция

It is the IP address of the Router1 interface that connects the PC1 LAN to Router1

Читайте также:
  1. A computer that is configured with the IPv6 address as shown in the exhibit is unable to access the internet. What is the problem?
  2. An IPv6 enabled device sends a data packet with the destination address of FF02::1.What is the target of this packet:all IPv6 enabled nodes on the local link
  3. Host IP Address: 183.91.104.16 Eleven bits have been borrowed to create the required subnets.
  4. Refer to the exhibit. PC1 issues an ARP request because it needs to send a packet to PC2. In this scenario, what will happen next:PC2 will send an ARP reply with its MAC address.
  5. The Graphical User Interface (Графічний Інтерфейс Користувача)
  6. Using the network in the exhibit, what would be the default gateway address for host A in the 192.133.219.0 network?
  7. What is a security feature of using NAT on a network:allows internal IP addresses to be concealed from external users
  8. Which address or combination of addresses does a Layer 3 switch use to make forwarding decisions:MAC and IP addresses
  9. Which statement is true about MAC addresses:The first three bytes are used by the vendor assigned OUI
  10. Адрес получателя (inside address).

 

During normal operation, from which location do most Cisco switches and routers run the IOS?

flash

RAM

NVRAM

disk drive

 

40
What is an important function of the physical layer of the OSI model?

It encodes frames into electrical, optical, or radio wave signals.

It accepts frames from the physical media.

It encapsulates upper layer data into frames.

It defines the media access method performed by the hardware interface.

 

41
Which procedure is used to reduce the effect of crosstalk in copper cables?

wrapping the bundle of wires with metallic shielding

avoiding sharp bends during installation

requiring proper grounding connections

designing a cable infrastructure to avoid crosstalk interference

Twisting opposing circuit wire pairs together

 

42
What are the three primary functions provided by Layer 2 data encapsulation? (Choose three.)

placement and removal of frames from the media

Detection of errors through CRC calculations

conversion of bits into data signals

Delimiting groups of bits into frames

Data link layer addressing

error correction through a collision detection method

session control using port numbers

 

43
What method is used to manage contention-based access on a wireless network?

token passing

CSMA/CD

CSMA/CA

priority ordering

 

44
What happens when part of an Internet radio transmission is not delivered to the destination?

A delivery failure message is sent to the source host.

The part of the radio transmission that was lost is re-sent.

The transmission continues without the missing portion.

The entire transmission is re-sent.

 

45
What is the auto-MDIX feature on a switch?

the automatic configuration of full-duplex operation over a single Ethernet copper or optical cable

The automatic configuration of an interface for a straight-through or a crossover Ethernet cable connection

the ability to turn a switch interface on or off accordingly if an active connection is detected

the automatic configuration of an interface for 10/100/1000 Mb/s operation

 

46
Which function is provided by TCP?

Detection of missing packets

communication session control

path determination for data packets

data encapsulation

 

47
How does a Layer 3 switch differ from a Layer 2 switch?

A Layer 3 switch learns the MAC addresses that are associated with each of its ports. However, a Layer 2 switch does not.

A Layer 3 switch maintains an IP address table instead of a MAC address table.

A Layer 3 switch supports VLANs, but a Layer 2 switch does not.


1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | 25 | 26 | 27 | 28 | 29 | 30 | 31 | 32 | 33 | 34 | 35 | 36 | 37 | 38 | 39 | 40 | 41 |

Поиск по сайту:



Все материалы представленные на сайте исключительно с целью ознакомления читателями и не преследуют коммерческих целей или нарушение авторских прав. Студалл.Орг (0.003 сек.)