Refer to the exhibit. What is wrong with the displayed termination?

The untwisted length of each wire is too long.*

The wires are too thick for the connector that is used.

The jack used is an RJ-11 connector instead of an RJ-45 connector.

The cable is not shielded.

19
Fill in the blank with a number.
10,000,000,000 b/s can also be written as ” 10 ” Gb/s.
20
What are two characteristics of 802.11 wireless networks? (Choose two.)

Collisions can exist in the networks. *

They are collision-free networks.

They use CSMA/CD technology.

Stations can transmit at any time.

They use CSMA/CA technology.*

21
A network administrator is required to upgrade wireless access to end users in a building. To provide data rates up to 1.3 Gb/s and still be backward compatible with older devices, which wireless standard should be implemented?

802.11n

802.11ac*

802.11g

802.11b
22
How is the magnetic field cancellation effect enhanced in UTP cables?

by decreasing the number of wires that are used to carry data

by increasing the thickness of the PVC sheath that encases all the wires

by increasing and varying the number of twists in each wire pair*

by increasing the thickness of the copper wires

23
Match the steps to the physical layer operations that occur when data is sent from one node and received at another node.

CCNA 1 R&S ITN Chapter 5 v5.0 Exam Answers 2014

2
A host is trying to send a packet to a device on a remote LAN segment, but there are currently no mappings in its ARP cache. How will the device obtain a destination MAC address?

It will send a request to the DNS server for the destination MAC address.

It will send an ARP request for the MAC address of the destination device.

It will send the frame and use its own MAC address as the destination.

It will send the frame with a broadcast MAC address.

It will send an ARP request for the MAC address of the default gateway.*

3
Which address or combination of addresses does a Layer 3 switch use to make forwarding decisions?

MAC and IP addresses*

MAC address only

MAC and port addresses

port address only

IP address only

4
What are two potential network problems that can result from ARP operation? (Choose two.)

Multiple ARP replies result in the switch MAC address table containing entries that match the MAC addresses of hosts that are connected to the relevant switch port.

On large networks with low bandwidth, multiple ARP broadcasts could cause data communication delays.*

Network attackers could manipulate MAC address and IP address mappings in ARP messages with the intent of intercepting network traffic.*

Manually configuring static ARP associations could facilitate ARP poisoning or MAC address spoofing.

Large numbers of ARP request broadcasts could cause the host MAC address table to overflow and prevent the host from communicating on the network.

Launch PT Hide and Save PT
Open the PT Activity. Perform the tasks in the activity instruction and then answer the question.

What destination address will PC1 include in the destination address field of the Ethernet frame that it sends to PC2?
00e0.b0be.8014

0030.a3e5.0401*

192.168.0.34

192.168.0.17

0007.ec35.a5c6

6
How does adding an Ethernet line card affect the form factor of a switch?

by increasing the back plane switching speed

by expanding the port density*

by expanding the NVRAM capacity

by making the switch stackable

7
Which two statements are correct about MAC and IP addresses during data transmission if NAT is not involved? (Choose two.)

Destination MAC addresses will never change in a frame that goes across seven routers.

A packet that has crossed four routers has changed the destination IP address four times.

Destination and source MAC addresses have local significance and change every time a frame goes from one LAN to another.*

Destination IP addresses in a packet header remain constant along the entire path to a target host.*

Every time a frame is encapsulated with a new destination MAC address, a new destination IP address is needed.

8
What is the Layer 2 multicast MAC address that corresponds to the Layer 3 IPv4 multicast address 224.139.34.56?

FE-80-00-0B-22-38

01-00-5E-0B-22-38*

FF-FF-FF-0B-22-38

00-00-00-0B-22-38

01-5E-00-0B-22-38

9
What is the purpose of the preamble in an Ethernet frame?

is used to identify the destination address

is used to identify the source address

is used as a padding for data

is used for timing synchronization*

10
A Layer 2 switch is used to switch incoming frames from a 1000BASE-T port to a port connected to a 100Base-T network. Which method of memory buffering would work best for this task?

level 1 cache buffering

shared memory buffering*

fixed configuration buffering

port-based buffering

11
A network administrator is connecting two modern switches using a straight-through cable. The switches are new and have never been configured. Which three statements are correct about the final result of the connection? (Choose three.)

The auto-MDIX feature will configure the interfaces eliminating the need for a crossover cable.*

The connection will not be possible unless the administrator changes the cable to a crossover cable.

The duplex capability has to be manually configured because it cannot be negotiated.

If both switches support different speeds, they will each work at their own fastest speed.

The link between switches will work as full-duplex.*

The link between the switches will work at the fastest speed that is supported by both switches.*

Refer to the exhibit. PC1 issues an ARP request because it needs to send a packet to PC2. In this scenario, what will happen next?​

RT1 will send an ARP reply with its Fa0/0 MAC address.​

PC2 will send an ARP reply with its MAC address.*

RT1 will send an ARP reply with the PC2 MAC address.​

SW1 will send an ARP reply with its Fa0/1 MAC address.​

SW1 will send an ARP reply with the PC2 MAC address.​

13
What is a characteristic of a contention-based access method?

It processes more overhead than the controlled access methods do.

It scales very well under heavy media use.

It is a nondeterministic method.*

It has mechanisms to track the turns to access the media.

14
What statement illustrates a drawback of the CSMA/CD access method?

Collisions can decrease network performance.*

Deterministic media access protocols slow network performance.

CSMA/CD LAN technologies are only available at slower speeds than other LAN technologies.

It is more complex than non-deterministic protocols.
15
When would a switch record multiple entries for a single switch port in its MAC address table?

when the switch is configured for Layer 3 switching

when another switch is connected to the switch port*

when a router is connected to the switch port

when multiple ARP broadcasts have been forwarded
16
Which two statements describe a fixed configuration Ethernet switch? (Choose two.)

An SVI cannot be configured on the switch.

A fixed configuration switch may be stackable.*

The number of ports on the switch cannot be increased.*

The port density of the switch is determined by the Cisco IOS.

The switch cannot be configured with multiple VLANs.

17
Which two statements describe features or functions of the logical link control sublayer in Ethernet standards? (Choose two.)

Logical link control is implemented in software.*

The LLC sublayer interacts directly with the NIC driver software.

The data link layer uses LLC to communicate with the upper layers of the protocol suite.*

The LLC sublayer is responsible for the placement and retrieval of frames on and off the media.

Logical link control is specified in the IEEE 802.3 standard.
18
A network administrator issues the following commands on a Layer 3 switch:

DLS1(config)# interface f0/3
DLS1(config-if)# no switchport
DLS1(config-if)# ip address 172.16.0.1 255.255.255.0
DLS1(config-if)# no shutdown
DLS1(config-if)# end

Поиск по сайту: